sand smooth and you will never know where it was. Since it is narrow and everything else around it is rock solid, you can simply fill the cut with your MIG or stick welder. Certain to get the OCD visitor into a cold sweatĪt risk of getting stoned, once you have your radius done, that cut will still be visible but much more shallow. it somehow conveys the concept that a perfectly straight crisp 90 degree edge is a requirement.īy the way I like the off centre bolting down provision of that Fisher. I sincerely don't know why manufacturers don't supply anvils with a small radius. This will show up as dead spots, sometimes just a corner others may be half or all the face. The main hidden fault is a delamination of the face and body. With any two piece anvil, Fishers have a foundry welded face so technically its a two piece anvil. The '7' casting mark on the foot indicates the nominal weight times ten. My questions: When did Fisher start or stop casting bolt-holes into the feet of the anvil Fisher first put the lugs on anvils in 1892. It is crisp edges from factory that cause most chips, well that and carelessness. As for weight markings, Fisher anvils were inconsistent in how they were marked. Checking anvils in the museum would put that anvils weight around 300 lbs. Radius is personal preference, but certainly necessary. Because small 100-130 anvils are very common they. For general work an anvil of 200 lbs or more is needed. A serious blacksmith will wear out a small anvil in a short time (a year or less). The London pattern anvil with less horn and heal in the same weight class is OK for light general work. And have a smaller even radius on the other side. The advantage of these small anvils is portability. Any thoughts on that plan?ĭepending on what you do on it, may be worth having a radius that starts as it is now and goes down gradually to nothing at the other end. I also havent found a true weight identification, despite a close inspection. LocationCorrales NM Posted JanuMy 400lb fisher anvil has a top plate size of 6X21. The middle position equals quarters (1/4) of a hundred weight. Rules: Any position can be zero, and IF zero is marked with a zero character (0). Enter digits from your anvil or other object. The oxidation is making it hard to see clearly. Commonly used to mark anvil weights before the adoption of the metric system in Great Britain. The left side is in much better condition, so I may sand a 3/32" or so radius on it. Looking at the logo, I am thinking it is a Fisher based on what I believe to be an eagle. Sawyers anvils are a heavy flat block used to tension or tune big circular saw blades. Up until this time all good anvils were forged from wrought iron and faced with tool steel that was forge welded to the body. They used a patent process that welded a tool steel plate onto a cast iron body in the mold when the anvil was cast. It would clean up nearly everything but the cut mark. Left, a 500 pound Fisher-Norris Eagle Sawyers anvil. 1843 - 1979 Fisher-Norris was the first large scale manufacturer of anvils in the U.S. I had considered continuing that radius the entire length of the right side. Given the lack of a logo I'm assuming it was perhaps cast in the 1950s or 60s? The only markings I've found so far is a "200" cast into the front right foot and an upside-down "R65" cast on the base below the heel, there is also what looks like a little tag mounted that says "14065".The guy I bought it from dressed that corner. I suppose the gray could be some sort of primer, but I suspect it may have been the original paint job and this was a navy anvil, I believe the Navy purchased Fishers exclusively. It seems to have a heavily flaking layer of creamish colored paint over, what appears to be Navy Gray. It has no logo-but I'm almost 100% sure it is a Fisher because of the shape, bolt lugs, and weight cast into the right front foot (200). You may not be able to tell from the photos but it looks like it has barely been used, needless to say I was not willing to leave the auction without it. I just picked up this anvil at an auction for a good price.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |